Thermalright Intel 12th/13th Generation LGA1700 Anti-Bending Buckle,CPU Stress Bending Correction Fixer, Curved Pressure Plate,Fully Fitted and Fixed Without Trace Installation (Black)

Works as advertised definitely dropped temps byba few degrees only thig I wish I did not say Intel 12 gen on it not really needed and especially when your using it on a 13th gen

Overall, Good frame, unfortunately I took off my old thermal grizzly (TG) paste and I went from an idle of 35⁰ to 42⁰ on a 13700k. So I reseated the cooler, same story. Finally I went to my microcenter and in a last ditch effort got more TG. After applying it, my cpu dropped to a cool 30⁰ this frame cost a fraction of TGs and gave me a 5⁰ drop and under load got my cpu to stop thermal throttling (on a liquid cooled system mind you)

Excellent product.

Works. Got my temps down a little bit.

Hello all. This is really a great product and works very well. Ive overclocked my 13600k to 5.5GHZ all cores and I never go over 50c while gaming I would really recommend it for you

I didn’t notice a change to my thermals, but it makes my install look cleaner

This is my first build in 4.5 years, so this time around I wanted to do tons of research. Im installing a CPU water cooler for the first time ever and researching that a fair amount led me to these CPU brackets. Ive never been satisfied with the cheezy, light weight CPU brackets/fasteners which come standad on MBs. This seemed like a valuable asset for just $14. Im running a 13th Gen Intel on an MSI Z690 ACE MB. As you can see from the pic, the fit looks very clean and the aluminum bracket is well machined. I do not know if temps will be lowered vs the stock guillotine bracket but it sure holds the Intel in place far better. And that can only be good.

Tengo una motherboard Z690-F de Asus y desde que coloqué el procesador intel i9 13900k hace 3 meses noté que quedó con demasiada presión con su soporte de CPU Stock. Decidí adquirir este LGA1700-BCF para quitarle esa presión al procesador, el cambiarlo fue realmente fácil ya que te incluye la llave para los tornillos que lo fijan a la motherboard. Las Temperaturas que obtenía en mi procesador eran realmente buenas, sin carga Variaban de 32 a 36 grados y con Cargas extremas pegaba a los 80 grados y más. Después de Cambiarlo noté que sin cargas está entre los 28 y 29 grados y con cargas obtuve en promedio 6 grados menos de Temperatura, el rating de mi cooler en Bios me dió un valor de 177 puntos lo cual es excelente para controlar las temperaturas. Este accesorio lo adquirí para evitar esas flexiones del procesador y cuidar su tiempo de vida lo más posible y no tanto por controlar las temperaturas, lo cual fue como un plus el obtener esos 3 o 6 grados menos en la temperatura. Cabe mencionar que tengo activo el overclocking de ASUS con frecuencias del procesador de hasta 6200MHZ. Si deseas cuidar tu inversión de 12va o 13va generación cambiando el adaptador stock, super recomendado este producto para reemplazar ese Frame LGA1700.

This product didnt reduce the temps too much, maybe 5C at full load. However, I got this product for the longevity of the CPU health. This way I can guarantee CPU bend doesnt happen over time.

Installed this on my Asus Maximus Z790 Hero with no problems. Used factory screws from motherboard and no issues. Make sure to tighten in criss cross pattern to make sure it tightens evenly and doesn’t bend. Highly recommend as this also lowered my CPU temps on my 13900k