Thermalright Intel 12th/13th Generation LGA1700 Anti-Bending Buckle,CPU Stress Bending Correction Fixer, Curved Pressure Plate,Fully Fitted and Fixed Without Trace Installation (Black)

Installed this on my Asus Maximus Z790 Hero with no problems. Used factory screws from motherboard and no issues. Make sure to tighten in criss cross pattern to make sure it tightens evenly and doesn’t bend. Highly recommend as this also lowered my CPU temps on my 13900k

Overall, Good frame, unfortunately I took off my old thermal grizzly (TG) paste and I went from an idle of 35⁰ to 42⁰ on a 13700k. So I reseated the cooler, same story. Finally I went to my microcenter and in a last ditch effort got more TG. After applying it, my cpu dropped to a cool 30⁰ this frame cost a fraction of TGs and gave me a 5⁰ drop and under load got my cpu to stop thermal throttling (on a liquid cooled system mind you)

When I bought my i7-13700K, the CPU would randomly spike to 100 °C while idle and stay at that temperature for 4 to 5 minutes. I upgraded my CPU cooler to a corsair 420 mm CPU watercooler, but the same issue occurred, although it didnt stay as long at 100 °C. The problem disappeared when I switched to the Thermalright contact frame. I also noticed an improvement in the average temperature of the CPU at idle and under load. It is clear that this contact frame helps the CPU behave in a better way, especially for a CPU that is known to overheat.

Dropped an average of 15C after I replaced the stock CPU bracket on my Gigabyte Aorus Elite AX. This fit very snug and secure on the 13th Gen i9 and I couldnt be happier!

This product didnt reduce the temps too much, maybe 5C at full load. However, I got this product for the longevity of the CPU health. This way I can guarantee CPU bend doesnt happen over time.

Tengo una motherboard Z690-F de Asus y desde que coloqué el procesador intel i9 13900k hace 3 meses noté que quedó con demasiada presión con su soporte de CPU Stock. Decidí adquirir este LGA1700-BCF para quitarle esa presión al procesador, el cambiarlo fue realmente fácil ya que te incluye la llave para los tornillos que lo fijan a la motherboard. Las Temperaturas que obtenía en mi procesador eran realmente buenas, sin carga Variaban de 32 a 36 grados y con Cargas extremas pegaba a los 80 grados y más. Después de Cambiarlo noté que sin cargas está entre los 28 y 29 grados y con cargas obtuve en promedio 6 grados menos de Temperatura, el rating de mi cooler en Bios me dió un valor de 177 puntos lo cual es excelente para controlar las temperaturas. Este accesorio lo adquirí para evitar esas flexiones del procesador y cuidar su tiempo de vida lo más posible y no tanto por controlar las temperaturas, lo cual fue como un plus el obtener esos 3 o 6 grados menos en la temperatura. Cabe mencionar que tengo activo el overclocking de ASUS con frecuencias del procesador de hasta 6200MHZ. Si deseas cuidar tu inversión de 12va o 13va generación cambiando el adaptador stock, super recomendado este producto para reemplazar ese Frame LGA1700.

I tried this modification because I didnt like how much torque was being applied to my CPU when using the stock fastener. I am not sure if it was actually bending the chip but it was under too much pressure in my opinion. Temps improved slightly. Easy to remove original and install and looks cleaner than original silver clamp. Comes with tool to remove and reinstall screws.

As per gamers nexus and jays two cents, this provided a better pressure distribution on my cpu. Low profile and more reliable than the stock bracket

No instructions. Luckily I found a youtube video

Hello all. This is really a great product and works very well. Ive overclocked my 13600k to 5.5GHZ all cores and I never go over 50c while gaming I would really recommend it for you