UPGRADED VERSION 3 PACK HEPA Replacement V10 Filters Compatible with Dyson V10 Cyclone series, V10 Absolute, V10 Animal, V10 Total Clean, V10 Motorhead, SV12, Part No. 969082-01, Washable and Reusable

(0 reviews)

Price
$19.99

Quantity
(10000 available )

Total Price
$79.95
Share
99 Ratings
80
14
3
1
1
Reviews
  • Brianna Smith

    > 3 day

    So, I was going back and forth debating whether or not to buy this off brand filter, or buy Dyson brand for a ton more money for only one filter... well, most would say more for less is a no brainer! But, it being Dyson, its expensive and I was weary on buying this. Well, I made the right decision and bought these. I read all the reviews.. One thing that is true, when first putting in the new replacement filter, its tight and you have to press down a little. After while, it does loosen up, but doesnt lose suction. I love the brush, it helps keeping the dust off between washes. Great choice and would buy again, even if they end up not lasting as long as the original, I would rather buy this one.

  • -=Wes=-

    > 3 day

    I was leery of buying non-OEM for the vacuum, but I couldn’t ignore the price. When they arrived, I compared to the OEM filter. The housing plastic is same thickness and color. The filter material is slightly different. I swapped in one of these on my vacuum. The vacuum works as well as before without issues. Once I got the filter change wanting, I examined the vacuum internals and it seemed there was no new dirt/dust versus before installing this filter. The filter itself was as dirty as the OEM filter was. I washed the filter and allowed it to air dry as the original. The filter dried within about 18 hours (lower humidity due to cold weather moving in). No visible wear or tearing on the filter. Will mark this filter and try again after cycling through remaining two.

  • Hobbyhobbit

    > 3 day

    These fit my V10 perfectly. Perhaps the filter fabric isn’t as fine as dyson OEM filters but these get the job done.

  • Frank

    Greater than one week

    Amazing “like new” performance of the machine!!! The only reason I didn’t give it a five was that the figment is a bit too tight. When first installed the vacuum did not work. I had to give it a scary extra twist to get it to seat. Next time it’s out I’m going to try and ascertain what bit if off and sand or grind off enough such that the fit is better. My worry is that over time I might crack something. The original filter has a crack along the back from years of use. It does and always has needed less effort to install than this one.

  • chandra williams

    > 3 day

    This is a great replacement. I use it to rotate when cleaning.

  • Scott

    Greater than one week

    Fit my Dyson like a factory filter. Great replacement for the price point

  • Perez

    > 3 day

    Since we had our Dyson Vacuum, we have been cleaning the filter as suggested in the user guide. This was a bit of a faff but worked up to a point. Eventually the filters started to smell and we noticed a loss of suction power. We decided to buy these replacement filters and they work very well. No more smell, much improved suction power. We have only had them a couple of weeks and although we use the Dyson most days it is early days. But we wont bother rinsing them again at the price we will just by more of these.

  • pnut

    > 3 day

    Just got these for my V10. The fit is a little tighter than the factory part. It took a little wiggling to get it to seat. Don’t know it that’s a good or bad thing, but I figure a tighter fit can’t be bad…. Better sealing on the o-rings!?!? Don’t know how it stands up to washing yet, but at these prices, I could just toss it and use a new one!

  • Patrick

    > 3 day

    Almost fit well like OEM but it works. Needs to force it in.

  • Maryann Sullivan

    > 3 day

    It definitely works but it’s very hard to get on and off.

Related products