Yamation DTF Powder Adhesive White 500g / 1.1lb DTF Transfer Powder Hot Melt Adhesive applies to All DTF Transfer Printers for Digital Prints on T-Shirts Textile DTF Supply with DTF PET Film and Ink

Fast delivery from Yamation. Have heard the brand from a friend. Good quality as expected. Willl buy more dtf transfer powder and film

This DTF powder works, and it works great on polyester shirts.

Quality of image looks great, transfer was nice and smooth. Do recommend.

I had high hopes but No it faded after first wash.

First time doing the sublimation hack and the t shirt came out amazing. Easy-to-use no smell or order. Ill definitely will buying this again. Highly recommend.

Easy to use. Works great. Does what it is supposed to. I would recommend this.

Smooth and fine DTF transfer powder. Works well with my DTF print. Fast delivery. Will buy again!

I think for the price that this should come in a canister as shown but instead it’s in a resealable bag that I can’t get to reclose. So I put this in a Tupperware container and seems to work just fine. There’s a learning curve to using this stuff so be sure to follow the direction and also, get on YouTube and watch some videos on how to use this. Depending on what type of heating device you use does make a difference. I’m not super happy with the results after washing. It seemed to fade on cotton after 1 wash. Maybe I didn’t leave the heat on long enough but like I said, there’s a learning curve until you figure out what works best for you.

Works great!

It has been a frustrating experience to do the sublimation DTF hack with Yamation film and powder - I went through about 25 sheets of film trying to get it to work (argh!). For anyone else frustrated with streaks/roller marks on their film, I found that I could change the print density by going to the Maintenance Tab (of my Epson SC-F100) and selecting Extended Settings. From there, I dragged the slider to the left so it was around -25%. This eliminated most streaking for me. If a design has a lot of black in it, maybe go even more negative with your number. If a design doesnt have much black at all, then go for a smaller negative number. I can get away with about -5% for an image with little to no black. Other things that might work for you are to choose the Rigid profile, or to choose Standard quality. But I use the Textile profile and high quality and then reduce the print density as described. I bake my powdered design at 385 degrees for 2 to 3 minutes on the bed of my HTVRont auto press. Obviously, I dont bring the press down, but just let it hover. Because it is a few inches above, it takes more than a minute. Because the sublimation ink has already been activated through this process, it isnt necessary to press the design at such a high temperature as you would with sublimation. After having conquered the problems with streaks, I then went about experimenting with pressing times, temps, and pressures. Following the recommendations on the package for temps and times did produce a nice result on the shirt, but the designs were degrading quickly upon washing. After a bunch of further experimentation, I found that I needed to do a higher temp and higher press time in order to have the design really adhere and last through washings. I think the success of this whole process really depends upon your equipment - basically your press and your printer and your ink. Be prepared for problems in figuring it out. Now that I HAVE figured it out for my setup, I do like the products and will continue to use them. But boy oh boy, was this a struggle to get it right! Note that for the Epson SC-F100, I do NOT need to apply the film to a piece of paper with tape, as others would tell you. It feeds right through my machine with no issues as is. If you have a different printer, your experience may be different. For anyone who has the HTVRont auto press trying to do this hack, put a pressing pillow beneath your garment to trick the press into applying more pressure. Also, for me, I need to press at 345 degrees for 45 seconds to get a good result and to get the design to last through washings. I do NOT do a second press with a teflon sheet on top as others recommend. This tends to remove ink and degrade the design in my experience. I find that after the first washing, the design feels more embedded into the fibers as it would if you did a second press anyway.