LIAN LI High Airflow Micro ATX PC Case, RGB Gaming Computer Case, Mesh Front Panel Mid-Tower Chassis with 2x140mm ARGB PWM Fans Pre-Installed, Tempered Glass Side Panel (LANCOOL 205M MESH, Snow)

This chassis is beautiful, nice design. Have nice filters with magnets, easy to manipulate with. There are also many ways to arrange the fans inside. I give it 4 stars because the interior is not designed the best. There is separate compartment on the bottom for power unit and hard disks. The cover that separates it with the rest of chassis, has only two holes to use for moving cables around. Both are close to the motherboard (once installed), and one hole is really impossible to use since the power unit will cover it. Speaking of it, make sure you do not buy power supply with rgbs since the fan will be facing bottoms. Unless you lie the tower sideways, there is no use for rgb power supply. The rest of components were easy to install (motherboard, AIO, memory, gpu..)

I ordered this case to upgrade the airflow to my pc as well as get some rgb into my setup. After installing my computer into the case, the rgb on the fans decided to stop working. It was clearly a problem with the fan controller on the back of the case. I decided to give the case another try and buy another one and return my faulty one. This time after installing my computer into the case, the rgb worked fine but the rgb controlling buttons on the front panel are faulty. The only reason why I’m not returning this one also is because I don’t want to go through the hassle of buying another case and swapping it over again. The Lconnwct software is a joke and doesn’t work with the case. I suggest you look for another case if you planned on buying this one. I will most likely never be buying a Lian li product again.

This case is wonderful! The airflow and build quality is exactly what you expect from Lian Li but my only issue is that it does not entirely fit a full ATX board and a 280mm AIO when it’s mounted in the top of the case. 4.5 stars imo

Overall very nice There was one Sata connection I couldnt use due to the case design, but no big deal Fans are big, and beutiful ARGB, but loud I wish the ARGB hub supported RGB so I could use the cases front panel switch to control my AIO No power/hdd lights or reset button, which is fine by me LOTS of space and ventilation inside, and very good access

When I bought this case, I was worried the great looks I saw in the thumbnail would be a front of a crappy poorly designed cheapo looking product in real life. I was pleasantly surprised to find the case lives up to its great looks and has a great build design. I really like the harddrive and power supply bay, as it just makes the build clean and keeps the clutter away from the view through the glass panel.

I am actually using a micro atx board so this case is overkill but i feel confident even with a larger board the cable management and overall desighn of the case would still give alot of space and the desighn is very slick some of the screws seemed to strip pretty easily but i was using the wrong screwdriver just trying to make it work and thats common in electronics that screws strip easily so it doesnt really bother me the metal case feels sturdy ive pulled on the bottom cover for the power supply with most of my strengh before realizing i needed to slide it and it still works like nothing happened no bends overall sturdy sexy case with usb3.0 for a good price it is my first pc build though still seems very solid and looks nice

I used the Lancool 205 Micro case for my first PC build and I couldnt be happier! Its an amazing micro case and I absolutely loved how it turned out. Im not at all an expert in PC building, but I hope that my feedback helps a bit! Here are my specs - GTX 1050 - GIGABYTE B550M DS3H - Crucial Ballistix 3200 MHz DDR4 - ARCTIC Freezer 34 eSports DUO - GIM KB-28 RGB Case Fans, 3 Pack White 120mm - EVGA 220-G3-0750-X1 Super Nova 750 G3, 80 Plus Gold 750W - Seagate BarraCuda 2TB Internal Hard Drive HDD - Crucial MX500 1TB - AMD Ryzen 5 3600 Pros - Really easy to work with - Lots of different ways to route cables - Simple and minimalist design - Micro tower is small enough to fit on top of a desk without looking too big - Air flow on the back, top, front, below the psu, and on the sides of the front panel (enough to fit total of 5 fans // 1 fan in the back, 2 fans on the top, and 2 fans in the front) - Removeable Magnetic dust filters on the top and the bottom - Fits the ARCTIC Freezer 34 Esports (grey/white) PERFECTLY, goodness I was worried that my cpu cooler wouldnt fit, but it fit absolutely perfect with a tiny bit of room between the tempered glass and the front of the cpu cooler - the gap in the front is big enough to fit a custom rgb panel - the temps are nice! my GPU runs around 35-41°C - the glass feels very high qu (its pretty heavy too!) Cons - I wasnt sure if this was the motherboard or the case (maybe it was just me?) but I found it very difficult mounting the motherboard onto the case. When I would screw the motherboard onto the case, I just could not get them to go inside. I managed to get the corners in, so I left it at that. This may have just been my fault though and I didnt want to strip the screws :( - This is me just being a little picky, but I wish the little raised cable management things in the back of the case (Im not sure what the technical term is) was slightly larger to fit bigger zip ties and velcro cable ties - I wasnt sure if the case was supposed to come with a mounting tray, but mine didnt come with any (Im still not sure if the mounting is included or not) so I put my HDD in the drive bay and I placed my SSD right on top of the drive bay and zip tied it down Overall, the microATX case is absolutely beautiful and very well made! Its user-friendly and great for beginners that want a smaller build!

WOW. Bought as a replacement for my Rosewill case to add more fans. You can fit two Noctua 140mm fans up top or an AIO as well as two Noctua 140mm fans in front. A Noctua 120mm fan for the rear fits like it was laser cut for my mobo. The cable management is easy and abundant. There are no rubber or plastic grommets, just folded over metal lips that are safe for even small, unprotected wires like my CPU cooler fan cable. There are magnetic mesh filters for the front and top fans. I will be purchasing from Lian Li again if I ever see a need to get another case. Cons: The two fans that come complimentary with the case burn out in a month. Dont bother attempting to use them like I did.

this is an amazing budget tower case. i had been looking at the corsair tower case for my build but went for this one instead and it’s been amazing and does its job. only reason i give this 4 stars instead of five is because my glass panel had shattered into pieces when i had tried to take it off a couple weeks after i finished building my pc. it was relatively easy to find a replacement panel but it really bummed me out

Great case if youre going for an AIO to cool, but if youre going air cooling you may want to look for a different case. as the front panel is very closed off and thus restricts airflow. Also, it does not come with all the fans needed. you will need to buy more for the top. I had to buy 2 140mm fans for the top. I was able to get the NZXT Kraken 280mm AIO to fit in the proper orientation in the front panel. Its a very very tight fit though, but it does fit. The 280 did not fit in the top of the case as it hits the motherboard. so you may want to look at a 240 for the top of the case. The Asus 3070 fits as well. Might be a little tight with a 3 fan card with the AIO in the front, but you will have to test that on your own. Great cable management in the back of the case and underneath as well.