KILMAT 50 mil 50 sqft Car Sound Deadening Mat, Butyl Automotive Sound Deadener, Audio Noise Insulation and dampening

2006 Dodge Charger Trunk Easy to install with the self adhesive. Use a roller to make sure its applied correctly. Live in Hawaii where its 85⁰ out. Went on easy, easy to cut, trim and mold around all the joints. Sound test after and the obnoxious rattle from the sub is gone. Used 1 box of the 50 sq ft 50mm Kilmat, completely covered the Trunk and 2 or 3 layers in trouble spots. Definitely going to be ordering more.

other than that perfect. i used a roll of tape and a can of peas and tomato sauce for the tight spaces. lil

I used this material to line the cab of my RV. Cab noise was so loud before installing this, that trying to listen to the radio was pointless. Pulled up my carpeting, and installed these sheets on floors, inside the doors and inside the dog-house, and what a difference. The RV cab stays comfortably cool, no more hot foot on the passenger side. The road noise is markedly improved, and we can carry on a conversation without having to shout over the motor. Would highly recommend this product. Very easy to use and definitely worth it if you want to improve a hot, noisy area in your vehicle.

My 2016 GMC Yukon XL has over 153K miles and was starting to exhibit a lot of unwanted creaks, rattles, and other unwanted noises. I applied about 10 sheets to the floor pan in the rear cargo area and under the second and third row seats and WOW, what a difference!! It tamed almost all of the rattles and quieted the ride overall. Im going to order another box or two and get to work on my Transit van (350HD,) 2014 Prius, and 2019 Tesla Model 3 next! Absolutely 1000% recommended!!

It is easy to handle, easy to cut, easy to apply just over all easy. The hardest part is probably the assembly and reassembly of your vehicle. I used this for my 2022 Nissan Altima.

I insultate the entire interior of my vintage VW Bus while restoring it and fell in love with this stuff. Easy to cut to size, GREAT adhesion and noise dampening. One NOTE.... It is REALLY important to wipe down the paint surface with a quality Wax and Grease Remover before you apply this product to ensure that it will stick well and permanently. Go Slo, Measure and cut carefully, clean, and apply, then use a separate specialty Seam tape to seal all the seams between pieces. Have Fun!!

Ive used other products before - Dynamat, second skin, etc. They worked well, but were $$. This product is cheaper, perhaps just slightly less thick - though, not by much. It also sticks well and seems to quiet things down quiet a bit. Frankly, you can almost double it up and stay under the price of the other leading brands. I would suggest wearing gloves. The adhesive doesnt come off, but the material will slice your hands up - like paper cuts. Not a lot of fun. Aside from that minor gripe, the product really is a great value!

I really like this product, it was super easy to lay out and trim to fit pieces where full sheets wouldnt fit. I could of taken more time and fit it a Bit better but in less than 30 minutes I did the entire floor of a 06 crew cab gmc 2500hd. I have not driven yet for noise test but just tapping on the floor you can instantly tell it will be helpful. My factory mass backing had water damage so I liked this for noise reduction and getting rid of the padding.

Adhesion and sound deadening are good for 50 mil. The sheets are large, which makes it harder to manage, especially if there are alot of curvature areas in vehicle.

I used these in my 2009 Jeep Wrangler all on the interior and it actually did a great job reducing noise. I used about half of the whole box covering the tub of it and the inside of the doors. It made the ride quiet and my sound system better because of the change of the acoustics. Takes time to install but is easy to cut with a stiff sharp knife. Buy a set of rollers with this though to make installation easier. Also, it takes about a whole day to install it. I have some left over I will probably use in a second car.